- Product Details
- Write a Comment
- Related Products
- After-sales Service
- Reviews (0)
Multi-language AUTOOL BT660 Battery Tester Built-in Thermal Printer BT-660 Battery Tester
Product specification:
Language: English, French, German, Spanish, Italian, Polish
1 One year warranty and lifetime maintenance
2Application12V automotive cranking lead acid battery and 12v/24v car system test
3Measure Range
CCA
100-3000
BCI
100-3000
CA
100-3000
MCA
100-3000
JIS
26A17--245H52
DIN
100-2500
IEC
100-2500
EN
100-2500
SAE
100-3000
GB
30AH-220AH
4Working Environment Temp:-10-50
5Special test clipDouble conductance Kelvin clamp
6Housing Material Acid-resistant ABS plastic
7Measure Range30AH-200AH
8Voltage Measure Range7-30VDC
How to use:
1.Connect the red test clamp with battery anode and the black one with cathode, the tester will power on automatically. Voltage battery
below 7.0VDC cant be tested properly, then press OK key to continue.
2.According to the tester, you can press UP/DOWN key to choose:
Battery Test
Cranking Test
Charging Test
Review Data
Print Data
Export Data to Computer
1Battery Test
Select the battery test and press OK key to continue:
Battery Type: select your battery type, usually is Regular Flooded
Input testing standard: the standard which you can see the front of the battery ,such as CCABCIDIN. If you cant find any info about the
standard, you can choose GB standard. Choose GB standards would lead little tolerance.
Input rated capacity: you can see the starting current standards in front of the battery .Such as BCI/300A.
Then press OK key to start testing.
Note
For power loss battery (such as a vehicle for a long time on hold, the battery is not charged in time; forget to close the lights, the doors
resulting in serious loss of battery electric vehicle and can not be started, etc.), in the actual testing process may also be prompted to
"Please replace the battery," for such batteries, please consult the battery manufacturers, and then tested.
2 Cranking Test
Starting the engine as prompted, tester will automatically complete the cranking test and display the result.
Normally, cranking voltage value lower than 9.6V is regarded as abnormal and it is OK if it is higher than 9.6V.
Test result of the tester includes actual cranking voltage and actual cranking time.
When cranking test is abnormal, battery test result will also be displayed at the same time.
3 Charging Test
When enter the charging test, tester will prompt "Loaded testing"
Note: Do not shut down the engine during the test. All electrical appliance and device are in OFF state. Turn on/off any electrical appliance
in the vehicle during the test will affect the accuracy of the test result.
Operate accordingly to increase the engine rotating speed to 2500turns, and keep for 5 seconds.
Tester starts the charging volt test after increase rev detected.
After the test finished, tester displays the effective charging volts, ripple test result and charging test result.
Charging Test Result:
1. Charging Volt: Normal. The generator output normal, no problem detected.
2. Charging Volt: Low. Check drive belt of the generator whether slip or running off. Check the connection between generator and battery
is normal or not. If both of the drive belt and the connection are in good condition, follow the manufacturer\\\'s suggestion to eliminate
generator fault.
3. Charging Volt: High. Since most of the vehicle generators are using internal regulator, the generator assembly has to be
replaced.(Some old style cars are using external regulator, then directly replace the regulator.) The normal high volt of the voltage
regulator is maximum 14.70.5V.If charging volt is too high, it will overcharge the battery. Therefore, the battery life will be shortened and
troubles will be caused.
4. No Volt Output. No generator volt output is detected. Check the generator connection cable, the drive belt of generator and engine
whether normal or not.
5. Diode Test: Through the test of charging current ripple, tester will find out whether the diode is normal or not. When ripple volt is too
high, it proves at least one diode is damaged. Check and replace the diode.
4Review Data
After entering the forth function, then press OK key you can view the final test result.
5Print Data
About Printing function, please contact with customer service.
6Export Data
Contact this battery tester to computer with Data Line, you can download the print software from our web at autooltech.com. If any
questions, please contact us.
Additional Function:
Press Menu to enter additional function:
LANGUAGE:
Support Multi-languages, such as English French Spainish etc , deatils pls check the package and the listing.
2.Time adjustment
Adjust system time.
Maybe you also like ...
- CGDI MB AC Adapter Work with Mercedes W164 W204 W221 W209 W246 W251 W166 for Dat.. /pieces (0) | Orders (5)
- V2018.12 BMW E/F Scanner II Full Version for BMW Diagnosis + IMMO + Mileage Corr.. /pieces (0) | Orders (5)
- Mercedes ME9.7 ME 9.7 ECU ECM Engine Computer Programming Meanwhile Compatible w.. /pieces (0) | Orders (5)
- Mercedes BEZN C6 OEM DOIP Xentry Diagnosis VCI Multiplexer with V2018.7 Software.. /pieces (0) | Orders (5)
- Cummins INLINE 7 Data Link Adapter with Insite 8.3 Software Multi-language Truck.. /pieces (0) | Orders (5)